Service
LED Lighting Upgrades in Alton, IL
Replacing incandescent or fluorescent lighting with suitable LED products can reduce lighting energy use and relamping work. Product ratings and actual results depend on the fixtures, controls, wiring, heat, and operating hours.
What an LED lighting upgrade is and what it saves
LED products can use substantially less electricity than incandescent lighting for similar brightness, and many are rated for much longer useful life. Justin can review the existing fixtures, wiring, dimmers, and panel as part of defining an LED project in an Alton or Metro East building.
Energy savings depend on the wattage replaced, the selected LED product, the number of fixtures, and daily operating hours. Comparing those inputs gives a more useful estimate than applying one savings percentage to every building.
Longer rated life can matter most in hard-to-reach locations such as stairwells, high ceilings, and shop bays. Actual life still depends on product quality, heat, fixture type, controls, and operating conditions.
What the job covers
Why an LED swap is more than changing bulbs
Done badly, an LED retrofit flickers, buzzes, or burns out early, and the savings go with it. Most of that traces back to what was already in the ceiling.
An LED upgrade with Lights Out Electric covers five things:
- Assess the existing fixtures, wiring, and dimmers for LED compatibility
- Recommend the right LED fixture, retrofit kit, or bulb for each space
- Install the selected fixtures and any wiring included in the agreed project scope
- Test dimming and controls for compatibility and operation
- Address removal and disposal of old fixtures in the project scope
The compatibility step is the one that gets skipped. An older dimmer built for a resistive incandescent load does not always read an LED driver correctly, which is where flicker and buzz come from. Enclosed fixtures trap heat that shortens LED life. And in an older Alton house the ceiling boxes themselves are sometimes the oldest thing in the room, which is why a lighting walk-through occasionally turns up original knob and tube still feeding the fixtures.
For a shop or a warehouse
Commercial LED lighting across the Metro East
In a commercial building, fixture count and operating hours can make lighting a meaningful part of electricity use and maintenance.
High bays, office troffers, fluorescent strips, exterior fixtures, and parking lighting each present different access and compatibility questions. Share the building hours and any shutdown constraints so Justin can tell you whether he can take the project on in the requested window.
Ameren Illinois may offer business energy-efficiency incentives for qualifying lighting projects. Eligibility and amounts depend on the current program and equipment, so check with Ameren Illinois before relying on an incentive. Related electrical work for a Metro East shop or storefront can be discussed during the same scope review.
Where lighting meets the rest of it
Lighting is the visible end of the wiring
A new fixture can still be fed by old wiring. Checking the circuit and fixture compatibility before ordering equipment can prevent surprises during installation.
If a lighting project involves a panel with no available space or capacity, the panel and service may need to be evaluated before the scope is finalized. Flicker that is not caused by a lamp or fixture may call for electrical troubleshooting. In a house, recessed, under-cabinet, and closet lighting can also be discussed with other residential electrical work and scoped together when appropriate.
Recommendations
How the work goes when Justin runs it
Sanderson A. recommends Lights Out Electric on Facebook.
Fast, Quick and Reliable. They were helpful and made the entire project hassle-free!
Common questions
LED lighting upgrade questions
Will switching to LED actually lower my electric bill?
LED products can reduce lighting electricity use compared with incandescent lighting for similar brightness. Actual savings depend on the products selected, the fixtures being replaced, how many lights are used, and how long they run.
Do LED bulbs work with my existing dimmers and fixtures?
Not every older fixture or dimmer pairs cleanly with every LED product, and a mismatch can cause flicker or buzz. A project assessment can include fixture, dimmer, wiring, and product compatibility before the scope is finalized.
How long do LED bulbs and fixtures last?
LED products may be rated for roughly 25,000 to 50,000 hours or more, compared with about 1,000 hours for a typical incandescent lamp. Actual useful life depends on the product, fixture, heat, controls, and operating conditions.
Can I just buy LED bulbs at the hardware store myself?
A straightforward lamp replacement may not need an electrician. Call when the project involves hardwired fixtures, buzzing dimmers, difficult access, older fluorescent equipment, or wiring questions so Justin can confirm whether electrical work is needed.
Do you do LED lighting for commercial buildings?
Lights Out Electric takes calls about commercial LED retrofits for shops, offices, storefronts, and other Metro East buildings. Justin reviews the existing fixtures, access, wiring, operating needs, and timing before scheduling the work. Check Ameren Illinois directly for current lighting-incentive eligibility and amounts.
Planning figures supplied by Lights Out Electric: LED products may be rated for 25,000 to 50,000 hours or more, compared with about 1,000 hours for an incandescent lamp, and can use 75 to 80% less electricity for equal or better brightness. Actual performance depends on the product, fixture, controls, heat, and operating conditions.
Pricing an LED swap in Alton or the Metro East?
Call and tell Justin what you want to light up. He will explain what needs to be assessed, then describe the scope and price before work starts.
Justin answers his own phone Mon to Fri, 7 to 3 100% recommended on Facebook